| Universal Boiler
Adapter |
|
 |
Parts include:
One Adapter
One 8" coupler band
One joint locking strap
One boiler collar clamp |
|
Universal Boiler Adapter is used horizontally or vertically to
adapt Saf-T Vent CI Plus to nominal diameter flue
collars. It can also adapt to boiler collars that
are slightly out of round. |
PIPE I.D. |
|
| A |
B |
| 5" |
7.3" |
| 6" |
8.3" |
| 7" |
9.3" |
| 8" |
10.3" |
| 9" |
11.3" |
| 10" |
12.3" |
| 12" |
14.3" |
| 14" |
16.3" |
| 16" |
18.3" |
| 18" |
20.3" |
| 20" |
22.3" |
| 22" |
24.3" |
| 24" |
26.3" |
| 26" |
28.3" |
| 28" |
30.3" |
| 30" |
32.3" |
| 32" |
34.3" |
| Guy Support Section |
|
 |
Parts include:
One Guy Support Section
One 5" long coupler
One joint locking strap |
|
Guy Support Section provides vertical support using
a part that is a flue-gas-carrying component of the
vent system. Guy sections are primarily installed in
long, inaccessible chases or used to provide support
to systems with extended lengths above the roofline.
Attach the guy section using stainless steel or
galvanized cables or chain (supplied by others). |
NOM. DIAM. |
|
| A |
B |
| 5" |
4.5" |
| 6" |
4.5" |
| 7" |
4.5" |
| 8" |
4.5" |
| 9" |
4.5" |
| 10" |
4.5" |
| 12" |
4.5" |
| 14" |
4.5" |
| 16" |
4.5" |
| 18" |
4.5" |
| 20" |
4.5" |
| 22" |
4.5" |
| 24" |
4.5" |
| 26" |
4.5" |
| 28" |
4.5" |
| 30" |
4.5" |
| 32" |
4.5" |
| Vertical Support with
4" clearance to combustibles |
|
 |
Parts include:
One Vertical Support |
|
Vertical Support with 4" clearance to combustibles
supports CI Plus vent systems. See the complete
installation instructions for placement. |
PIPE I.D. |
A |
| 5" |
7.3" |
| 6" |
8.3" |
| 7" |
9.3" |
| 8" |
10.3" |
| 9" |
11.3" |
| 10" |
12.3" |
| 12" |
14.3" |
| 14" |
16.3" |
| 16" |
18.3" |
| 18" |
20.3" |
| 20" |
22.3" |
| 22" |
24.3" |
| 24" |
26.3" |
| 26" |
28.3" |
| 28" |
30.3" |
| 30" |
32.3" |
| 32" |
34.3" |
| Vertical Support with
1" clearance to combustibles |
|
 |
Parts include:
One Vertical Support |
|
Vertical Support with 1" clearance to combustibles
supports CI Plus vent systems. See the complete
installation instructions for placement. |
PIPE I.D. |
A |
| 5" |
7.3" |
| 6" |
8.3" |
| 7" |
9.3" |
| 8" |
10.3" |
| 9" |
11.3" |
| 10" |
12.3" |
| 12" |
14.3" |
| 14" |
16.3" |
| 16" |
18.3" |
| 18" |
20.3" |
| 20" |
22.3" |
| 22" |
24.3" |
| 24" |
26.3" |
| Horizontal Support for
large diameter |
|
 |
Parts include:
One Horizontal Support |
|
Horizontal Support for large diameter vent systems.
Diameters 24" through 32" must have support every 6
feet of horizontal run. The support may be attached
from the center of the bracket or from the sides of
the support bracket. Support hangers by themselves
do not maintain the necessary clearances to
combustible materials- be certain to consider
clearances when planning the system. |
PIPE I.D. |
|
| A |
B |
| 24" |
26.3" |
| 26" |
28.3" |
| 28" |
30.3" |
| 30" |
32.3" |
| 32" |
34.3" |
| Support Clamp |
|
 |
Parts include:
One Support Clamp set (two halves)
Two 1/4-20 nuts and bolts |
|
Horizontal Support for smaller diameter vent systems
to provide support at required 6-foot intervals.
Support clamps by themselves do not maintain the
necessary clearances to combustible materials- be
certain to consider clearances when planning the
system. This part is manufactured of 18 gauge,
type 304 stainless steel and should not be installed
in the direct path of flue gases. |
PIPE I.D. |
|
| A |
B |
| 5" |
7" |
| 6" |
8" |
| 7" |
9" |
| 8" |
10" |
| 9" |
11" |
| 10" |
12" |
| 12" |
14" |
| 14" |
16" |
| 16" |
18" |
| 18" |
20" |
| 20" |
22" |
| 22" |
24" |
| Roof Jack Support
System |
|
 |
Parts include:
One Roof Jack Support
One Storm Collar |
|
Roof Jack Support System is for use with vertical
terminations. Use to pass through combustible and
non-combustible roof structures. The roof jack
support system must be installed on a flat roof or a
level curb only (see
Roof Products & Systems for acceptable roof
curbs). Can not be used in a chase with a
1" clearance to vent. See Tall Cone Flashing. |
PIPE I.D. |
A |
B |
C |
D |
E |
| 5" |
7.5" |
10.1" |
7.25" |
15" |
24" |
| 6" |
8.5" |
11.1" |
7.25" |
15" |
24" |
| 7" |
9.5" |
12.1" |
7.25" |
15" |
24" |
| 8" |
10.5" |
13.1" |
7.25" |
15" |
24" |
| 9" |
11.5" |
14.5" |
7.25" |
15" |
24" |
| 10" |
12.5" |
15.1" |
7.25" |
15" |
24" |
| 12" |
14.5" |
17.1" |
7.25" |
15" |
24" |
| 14" |
16.5" |
19.1" |
7.25" |
15" |
27" |
| 16" |
18.5" |
21.1" |
7.25" |
15" |
30" |
| 18" |
20.5" |
23.1" |
7.25" |
15" |
32" |
| 20" |
22.5" |
25.1" |
7.25" |
15" |
34" |
| 22" |
24.5" |
27.1" |
7.25" |
15" |
36" |
| 24" |
26.5" |
29.1" |
7.25" |
15" |
36" |
| 26" |
28.5" |
31.1" |
7.25" |
15" |
36" |
| 28" |
30.5" |
33.1" |
7.25" |
15" |
40" |
| 30" |
32.5" |
35.1" |
7.25" |
15" |
42" |
| 32" |
34.5" |
37.1" |
7.25" |
15" |
44" |
| Tall Cone Flashing and
Support |
|
 |
Parts include:
One Tall Cone Flashing
One Storm Collar
Support screws |
|
Tall Cone Flashing and Support is used as a vertical
roof penetration/support in conjunction with a
combustible chase. Can be used with a roof curb if
needed (see
Roof Products & Systems for acceptable roof
curbs). Can be used on metal roofs with a 2/12
pitch. All stainless steel construction. A Vented
Termination Collar must be used when
installed in a combustible chase and must be ordered
separately. Caution: support screws can only
be installed with Saf-T Vent CI Plus venting. |
PIPE I.D. |
A |
B |
C |
D |
NO. HOLES |
| 5" |
7.5" |
10.75" |
20" |
12" |
4 |
| 6" |
8.5" |
11.75" |
20" |
12" |
4 |
| 7" |
9.5" |
12.75" |
22" |
12" |
4 |
| 8" |
10.5" |
13.75" |
22" |
12" |
4 |
| 9" |
11.5" |
14.75" |
24" |
12" |
4 |
| 10" |
12.5" |
15.75" |
24" |
12" |
4 |
| 12" |
14.5" |
17.75" |
26" |
12" |
4 |
| 14" |
16.5" |
19.75" |
28" |
12" |
6 |
| 16" |
18.5" |
21.75" |
30" |
16" |
6 |
| 18" |
20.5" |
23.75" |
32" |
12" |
6 |
| 20" |
22.5" |
25.75" |
34" |
12" |
6 |
| 22" |
24.5" |
27.75" |
36" |
12" |
6 |
| 24" |
26.5" |
29.75" |
38" |
12" |
8 |
| 26" |
28.5" |
31.75" |
40" |
12" |
8 |
| 28" |
30.5" |
33.75" |
42" |
12" |
8 |
| 30" |
32.5" |
35.75" |
44" |
12" |
8 |
| 32" |
34.5" |
37.75" |
46" |
12" |
8 |
| Pitched Tall Cone
Flashing |
|
 |
Parts include:
One Pitched Tall Cone Flashing
One Storm Collar |
|
Pitched Tall Cone Flashing and Support is used as a
vertical roof penetration in conjunction with a
combustible chase. Can be used on roofs with a 2/12
- 6/12
pitch. All stainless steel construction. A Vented
Termination Collar must be used when
installed in a combustible chase and must be ordered
separately. |
PIPE I.D. |
A |
B |
| 5" |
8.5" |
24" |
| 6" |
9.5" |
24" |
| 7" |
10.5" |
26" |
| 8" |
11.5" |
26" |
| 9" |
12.5" |
26" |
| 10" |
13.5" |
28" |
| 12" |
15.5" |
30" |
| 14" |
17.5" |
34" |
| 16" |
19.5" |
34" |
| 18" |
21.5" |
36" |
| 20" |
23.5" |
38" |
| 22" |
25.5" |
40" |
| 24" |
27.5" |
42" |
| 26" |
29.5" |
44" |
| 28" |
31.5" |
46" |
| 30" |
33.5" |
48" |
| 32" |
35.5" |
48" |
|
|
All information is subject to change without notice. Dimensions and specifications shown are within
manufacturing tolerances.
© Copyright Commercial Products Group of Hart & Cooley, Inc., October, 2007. All Rights Reserved.
